The Zodiac Pacer attaches to a pool skimmer or a dedicated cleaner (suction) line. Dirt and debris are drawn straight into the pool filtration system when water runs through the cleaner.
In This Article...
What is the operation of a robotic pool cleaner?
To remove dirt and debris from the pool, robot cleaners use an electric motor to create suction. Rotating brushes are also used by most models to aid dislodge more persistent particles, such as algae.
Why isn’t the suction in my zodiac pool moving?
The Zodiac suction pool cleaner is Australia’s best-selling pool cleaner.
Zodiac diaphragm technology powers it. There are no wheels, cogs, or loud hammers, resulting in a whisper-quiet operation and reduced maintenance costs.
Before we begin troubleshooting your Zodiac pool cleaner, make sure your filtration system has been back washed or cleaned.
Now, as you recall from lesson one, it’s also critical to wipe out your skimmer basket and pump basket thoroughly. This will ensure that your Zodiac pool cleaner has enough suction flow to function properly.
It’s now time for troubleshooting, where we’ll look for answers to your most often asked questions.
What if my cleaner stops and starts?
The first thing you should do if your Zodiac pool cleaner stops and begins is check the suction flow coming through the hose. This operation will necessitate the use of your pump.
A pool pulse is included with this Zodiac pool cleaner, and it has numbers on it. Put this on the end of the hose, under the water, with the suction flow coming through, and place it around number two.
If number two doesn’t work, the AD valve in the skimmer box is the next thing to check. The AD valve is pre-programmed to number two. We raise it to number three if we want additional suction. This could also help if your pool cleaner isn’t scaling the walls well enough.
If the pool cleaner still isn’t working properly after we’ve done that, we should look for leaks in the hose. At each joint, we remove the hose out of the water and listen for leaks. That’s something we’d like to do all the way around the hose.
The diaphragm within the Zodiac cleaner is the next thing we should look at. It’s a good idea to turn off your pump and filter at this point since you don’t want any air to leak through the hose while we’re checking.
So remove the Zodiac diaphragm and inspect it for any tears or obstructions. If it appears to be in good working order, replace it and contact your local pool professional, as there may be a more serious problem with the system. It’s possible that your filtration system has an air leak, or that something has become stuck inside the pipework leading back to your filtration system.
What if my cleaner is patterning and not covering the pool properly?
If your cleaner is not effectively patterning and covering the pool, make sure the water flow from all return inlets is directed downward and toward each other, or downward and toward the pool’s center.
This will help to prevent water from interfering with the Zodiac hose’s natural movement. If you can’t divert the water deep enough down in the pool, or if your existing eyeballs don’t divert far enough, an Aim Flow Diverter like this one from your local pool specialist might be a good solution. The Aim Flow Diverter is a device that pushes into the return line to divert water to the pool’s bottom.
To relax the memory, take the cleaner out of the pool and lay the hose in a straight line in the sun. For the better part of a day, leave it there. Check that the cleaner’s hose is the correct length before reinstalling it in the pool. If the pool cleaner is still patterning and not properly covering the pool, as indicated in lesson one, you may need to add one or two extra hose lengths.
It’s also crucial to adjust the hose weight such that it sits at the end of the first hose length, the leader hose.
What if my cleaner is not cleaning the pool?
If you reside in an area with a lot of leaves or huge debris like gum nuts, you might think about getting a Polaris pool cleaning. Any huge debris that a suction cleaner won’t be able to pick up will be picked up by a Polaris.
If you’re still having issues after consulting your manual and troubleshooting your cleaner, it’s possible that it’s not the right cleaner for your pool.
Expert tips
Before backwashing your filter, make sure your Zodiac pool cleaner is turned off.
If your vacuum cleaner starts and stops:
- Using your pool pulse, check the suction flow.
- Examine the AD valve.
- Check for air leaks in the pool cleaner hose.
- Check your Zodiac pool cleaner’s diaphragm.
If your pool cleaner is patterning rather than covering the pool, it’s most likely because:
- Verify that the water flow from all of the returning inlets is directed properly.
- It’s possible that an Aim Flow Diverter will need to be installed in the pool’s return inlet.
- To ease the memories, lay the hose directly in the sun.
- Also, make sure you have the correct hose length and that the hose weight is adjusted.
- If your pool cleaner turns over, check the suction flow with the pool pulse and free any jams using the cleaner’s swivel.
- Finally, if your pool cleaner isn’t cleaning the pool properly, consider a Polaris pool cleaner.
Is it possible to leave a robotic pool cleaner in the pool?
While your bot cleans the pool, you can swim, but it’s best not to. Swimming causes the water to swirl. If the machine is in the water at the time, it will be buffeted by the river, making it more difficult for it to fulfill its task. To cover the same amount of ground, it will have to work harder.
The change in pH can harm the plastic if you keep the machine in the water while adding chlorine. Exposure to the sun on a regular basis may cause the plastic to wear out faster than it would otherwise.
It’s possible that you’ll only need to perform the cycle two or three times every week. Allowing the machine to sit in the water for that long exposes it to the elements. The seals may deteriorate more quickly as a result of this exposure, allowing for leaks and harm to the electronic components.
What happens to the debris from a pool vacuum?
The vacuuming procedure is similar for pools with a sand filter:
- First, determine the amount of dirt and particles in your pool and adjust the filter’s valve settings accordingly.
- To start the vacuum process, fill the vacuum hose with water, connect it to the vacuum plate or skimmer disk, and set it directly atop the suction vent.
- Slowly and steadily move the suction head across the pool’s surface.
- Dirt and debris will be sucked into the pump through the suction plate. After that, it’ll go through the sand filter.
- The surplus particles should be captured by the filter, depending on the parameters.
- After you’ve finished vacuuming the pool, make sure to backwash your sand filter.
What’s going on with my Zodiac creepy crawly?
- Is the drain in the pool closed? Drain the water.
- Is the pool filter in good working order? Ensure that the filter is clean.
- Is the pump strainer basket in good condition? Empty the basket.
- Is there debris in the cleaner’s bottom? Debris should be removed.
- Is there any air leaking through the hose? Replace the portion that is leaking.
- Is there a blockage in the skimmer connector? Regulator valve should be cleaned.
- Check sure the main drain and all suction lines are closed, except the one that Kreepy Krauly is connected to (usually a skimmer).
- Examine the filter or for debris.
- Check the Kreepy Krauly flapper for debris. Debris could obstruct flapper movement.
- It’s possible that the pool pump and filter system are insufficient (incapable of providing enough water flow).
- Make sure the pool pump isn’t running at a low speed.
What’s wrong with my robotic pool cleaner?
Because robotic pool cleaners do not rely on any of the pool’s connections to function, you know the issue isn’t there. Check the power cord if your robotic pool cleaner stops moving. It’s possible that it’s not plugged in correctly or that there’s a problem with the power supply.
Make that the power supply’s indication light is turned on. If it is, but the pool cleaner still does not move, the issue is with the cleaner. Examine the cord for any rips or tears that could be causing a short circuit.
You may have an issue with the drive motor even though all of the cords are in good working order and the power supply is turned on. All of the connections must be secure, and electricity must be available. If electricity isn’t reaching the drive motor or the motor isn’t responding, it’s possible that your pool cleaner needs a new drive motor.
As you can see, determining why your pool cleaner isn’t moving is a time-consuming process, regardless of the sort of pool cleaner you have. Finding the cause of your pool cleaner’s inability to move is difficult, even after checking for simple leaks or disconnected hoses and ensuring the power line is turned on.
Is Zodiac and Barracuda the same thing?
BARACUDA was introduced in the early 1980s with a completely new diaphragm technology, which set it apart from its competitors by allowing for quieter operation and greater maneuverability. The diaphragm mechanism developed by BARACUDA is still utilized in disc suction pool cleaners today.
From an office in Frenchs Forest, New South Wales, a local Australian began importing and selling BARACUDA in 1986.
When should a swimming pool be vacuumed?
Vacuuming your pool once a week is a good idea in general. If you detect a lot of trash, dirt, or leaves on the pool’s floor, you should vacuum it (for example, your pool may need vacuuming after a heavy storm).